-- Copyright (C) 2018 Intel Corporation. All rights reserved. -- Your use of Intel Corporation's design tools, logic functions -- and other software and tools, and its AMPP partner logic -- functions, and any output files from any of the foregoing -- (including device programming or simulation files), and any -- associated documentation or information are expressly subject -- to the terms and conditions of the Intel Program License -- Subscription Agreement, the Intel Quartus Prime License Agreement, -- the Intel FPGA IP License Agreement, or other applicable license -- agreement, including, without limitation, that your use is for -- the sole purpose of programming logic devices manufactured by -- Intel and sold by Intel or its authorized distributors. Please -- refer to the applicable agreement for further details. -- -- This is a Quartus Prime output file. It is for reporting purposes only, and is -- not intended for use as a Quartus Prime input file. This file cannot be used -- to make Quartus Prime pin assignments - for instructions on how to make pin -- assignments, please see Quartus Prime help. --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- -- NC : No Connect. This pin has no internal connection to the device. -- DNU : Do Not Use. This pin MUST NOT be connected. -- VCCINT : Dedicated power pin, which MUST be connected to VCC (1.2V). -- VCCIO : Dedicated power pin, which MUST be connected to VCC -- of its bank. -- Bank 1A: 3.3V -- Bank 1B: 3.3V -- Bank 2: 1.8V -- Bank 3: 3.3V -- Bank 5: 1.8V -- Bank 6: 1.8V -- Bank 8: 3.3V -- GND : Dedicated ground pin. Dedicated GND pins MUST be connected to GND. -- It can also be used to report unused dedicated pins. The connection -- on the board for unused dedicated pins depends on whether this will -- be used in a future design. One example is device migration. When -- using device migration, refer to the device pin-tables. If it is a -- GND pin in the pin table or if it will not be used in a future design -- for another purpose the it MUST be connected to GND. If it is an unused -- dedicated pin, then it can be connected to a valid signal on the board -- (low, high, or toggling) if that signal is required for a different -- revision of the design. -- GND+ : Unused input pin. It can also be used to report unused dual-purpose pins. -- This pin should be connected to GND. It may also be connected to a -- valid signal on the board (low, high, or toggling) if that signal -- is required for a different revision of the design. -- GND* : Unused I/O pin. Connect each pin marked GND* directly to GND -- or leave it unconnected. -- RESERVED : Unused I/O pin, which MUST be left unconnected. -- RESERVED_INPUT : Pin is tri-stated and should be connected to the board. -- RESERVED_INPUT_WITH_WEAK_PULLUP : Pin is tri-stated with internal weak pull-up resistor. -- RESERVED_INPUT_WITH_BUS_HOLD : Pin is tri-stated with bus-hold circuitry. -- RESERVED_OUTPUT_DRIVEN_HIGH : Pin is output driven high. --------------------------------------------------------------------------------- --------------------------------------------------------------------------------- -- Pin directions (input, output or bidir) are based on device operating in user mode. --------------------------------------------------------------------------------- Quartus Prime Version 18.1.0 Build 625 09/12/2018 SJ Standard Edition CHIP "TEST" ASSIGNED TO AN: 10M16SAU169C8G Pin Name/Usage : Location : Dir. : I/O Standard : Voltage : I/O Bank : User Assignment ------------------------------------------------------------------------------------------------------------- GND : A1 : gnd : : : : RESERVED_INPUT_WITH_WEAK_PULLUP : A2 : : : : 8 : RESERVED_INPUT_WITH_WEAK_PULLUP : A3 : : : : 8 : RESERVED_INPUT_WITH_WEAK_PULLUP : A4 : : : : 8 : RESERVED_INPUT_WITH_WEAK_PULLUP : A5 : : : : 8 : CTRL_3V3_INT_C : A6 : input : 3.3-V LVTTL : : 8 : Y CTRL_3V3_MODPRS_E : A7 : input : 3.3-V LVTTL : : 8 : Y CTRL_3V3_MODPRS_A : A8 : input : 3.3-V LVTTL : : 8 : Y CTRL_3V3_RST_B : A9 : output : 3.3-V LVTTL : : 8 : Y CTRL_3V3_MODSEL_F : A10 : output : 3.3-V LVTTL : : 8 : Y CTRL_3V3_RST_J : A11 : output : 3.3-V LVTTL : : 8 : Y QSFP_INT_G : A12 : output : 1.8 V : : 6 : Y GND : A13 : gnd : : : : CTRL_3V3_MODPRS_H : B1 : input : 3.3-V LVTTL : : 1A : Y RESERVED_INPUT_WITH_WEAK_PULLUP : B2 : : : : 8 : RESERVED_INPUT_WITH_WEAK_PULLUP : B3 : : : : 8 : RESERVED_INPUT_WITH_WEAK_PULLUP : B4 : : : : 8 : CTRL_3V3_MODPRS_J : B5 : input : 3.3-V LVTTL : : 8 : Y RESERVED_INPUT_WITH_WEAK_PULLUP : B6 : : : : 8 : RESERVED_INPUT_WITH_WEAK_PULLUP : B7 : : : : 8 : GND : B8 : gnd : : : : CTRL_3V3_INT_B : B9 : input : 3.3-V LVTTL : : 8 : Y CTRL_3V3_MODPRS_G : B10 : input : 3.3-V LVTTL : : 8 : Y QSFP_MODPRS_H : B11 : output : 1.8 V : : 6 : Y QSFP_INT_F : B12 : output : 1.8 V : : 6 : Y QSFP_MODPRS_F : B13 : output : 1.8 V : : 6 : Y CTRL_3V3_MODPRS_D : C1 : input : 3.3-V LVTTL : : 1A : Y RESERVED_INPUT_WITH_WEAK_PULLUP : C2 : : : : 1A : GND : C3 : gnd : : : : ~ALTERA_nSTATUS~ / RESERVED_INPUT : C4 : input : 3.3 V Schmitt Trigger : : 8 : Y ~ALTERA_CONF_DONE~ / RESERVED_INPUT : C5 : input : 3.3 V Schmitt Trigger : : 8 : Y VCCIO8 : C6 : power : : 3.3V : 8 : VCCIO8 : C7 : power : : 3.3V : 8 : VCCIO8 : C8 : power : : 3.3V : 8 : CTRL_3V3_INT_J : C9 : input : 3.3-V LVTTL : : 8 : Y CTRL_3V3_INT_D : C10 : input : 3.3-V LVTTL : : 8 : Y QSFP_MODPRS_G : C11 : output : 1.8 V : : 6 : Y QSFP_MODPRS_D : C12 : output : 1.8 V : : 6 : Y QSFP_INT_J : C13 : output : 1.8 V : : 6 : Y CTRL_3V3_INT_H : D1 : input : 3.3-V LVTTL : : 1A : Y ANAIN1 : D2 : : : : : ADC_VREF : D3 : : : : : VCCA3 : D4 : power : : 3.0V/3.3V : : GND : D5 : gnd : : : : RESERVED_INPUT_WITH_WEAK_PULLUP : D6 : : : : 8 : ~ALTERA_CONFIG_SEL~ / RESERVED_INPUT : D7 : input : 3.3-V LVTTL : : 8 : Y CTRL_3V3_RST_F : D8 : output : 3.3-V LVTTL : : 8 : Y QSFP_RST_A : D9 : input : 1.8 V : : 6 : Y VCCA2 : D10 : power : : 3.0V/3.3V : : QSFP_MODSEL_G : D11 : input : 1.8 V : : 6 : Y QSFP_MODPRS_J : D12 : output : 1.8 V : : 6 : Y RESERVED_INPUT_WITH_WEAK_PULLUP : D13 : : : : 6 : CTRL_3V3_INT_E : E1 : input : 3.3-V LVTTL : : 1A : Y REFGND : E2 : : : : : CTRL_3V3_MODPRS_F : E3 : input : 3.3-V LVTTL : : 1A : Y CTRL_3V3_INT_G : E4 : input : 3.3-V LVTTL : : 1A : Y RESERVED_INPUT_WITH_WEAK_PULLUP : E5 : : : : 1B : RESERVED_INPUT_WITH_WEAK_PULLUP : E6 : : : : 8 : ~ALTERA_nCONFIG~ / RESERVED_INPUT : E7 : input : 3.3 V Schmitt Trigger : : 8 : Y CTRL_3V3_MODPRS_C : E8 : input : 3.3-V LVTTL : : 8 : Y QSFP_INT_D : E9 : output : 1.8 V : : 6 : Y QSFP_INT_H : E10 : output : 1.8 V : : 6 : Y GND : E11 : gnd : : : : QSFP_RST_J : E12 : input : 1.8 V : : 6 : Y QSFP_RST_F : E13 : input : 1.8 V : : 6 : Y CTRL_3V3_INT_F : F1 : input : 3.3-V LVTTL : : 1A : Y VCCIO1A : F2 : power : : 3.3V : 1A : GND : F3 : gnd : : : : CTRL_3V3_LPMOD_A : F4 : output : 3.3-V LVTTL : : 1B : Y ~ALTERA_TDI~ / RESERVED_INPUT_WITH_WEAK_PULLUP : F5 : input : 3.3 V Schmitt Trigger : : 1B : Y ~ALTERA_TDO~ : F6 : output : 3.3-V LVTTL : : 1B : Y VCC_ONE : F7 : power : : 3.0V/3.3V : : QSFP_INT_E : F8 : output : 1.8 V : : 6 : Y RESERVED_INPUT_WITH_WEAK_PULLUP : F9 : : : : 6 : RESERVED_INPUT_WITH_WEAK_PULLUP : F10 : : : : 6 : VCCIO6 : F11 : power : : 1.8V : 6 : QSFP_MODPRS_E : F12 : output : 1.8 V : : 6 : Y QSFP_RST_B : F13 : input : 1.8 V : : 6 : Y ~ALTERA_TMS~ / RESERVED_INPUT_WITH_WEAK_PULLUP : G1 : input : 3.3 V Schmitt Trigger : : 1B : Y ~ALTERA_TCK~ / RESERVED_INPUT : G2 : input : 3.3 V Schmitt Trigger : : 1B : Y VCCIO1B : G3 : power : : 3.3V : 1B : CTRL_3V3_MODSEL_D : G4 : output : 3.3-V LVTTL : : 1B : Y QSFP_LPMOD_D : G5 : input : 1.8 V : : 2 : Y VCC_ONE : G6 : power : : 3.0V/3.3V : : GND : G7 : gnd : : : : VCC_ONE : G8 : power : : 3.0V/3.3V : : QSFP_INT_B : G9 : output : 1.8 V : : 6 : Y QSFP_MODSEL_F : G10 : input : 1.8 V : : 6 : Y VCCIO6 : G11 : power : : 1.8V : 6 : QSFP_LPMOD_G : G12 : input : 1.8 V : : 5 : Y QSFP_INT_C : G13 : output : 1.8 V : : 5 : Y RESERVED_INPUT_WITH_WEAK_PULLUP : H1 : : : : 1B : CTRL_3V3_LPMOD_D : H2 : output : 3.3-V LVTTL : : 1B : Y CTRL_3V3_MODSEL_E : H3 : output : 3.3-V LVTTL : : 1B : Y QSFP_AUX_0 : H4 : bidir : 1.8 V : : 2 : Y QSFP_RST_E : H5 : input : 1.8 V : : 2 : Y QSFP_LPMOD_A : H6 : input : 1.8 V : : 2 : Y VCC_ONE : H7 : power : : 3.0V/3.3V : : QSFP_MODPRS_C : H8 : output : 1.8 V : : 5 : Y QSFP_AUX_1 : H9 : bidir : 1.8 V : : 5 : Y QSFP_LPMOD_J : H10 : input : 1.8 V : : 5 : Y VCCIO5 : H11 : power : : 1.8V : 5 : GND : H12 : gnd : : : : QSFP_AUX_2 : H13 : bidir : 1.8 V : : 5 : Y QSFP_MODSEL_E : J1 : input : 1.8 V : : 2 : Y QSFP_MODSEL_D : J2 : input : 1.8 V : : 2 : Y VCCIO2 : J3 : power : : 1.8V : 2 : GND : J4 : gnd : : : : CTRL_3V3_MODSEL_A : J5 : output : 3.3-V LVTTL : : 3 : Y RESERVED_INPUT_WITH_WEAK_PULLUP : J6 : : : : 3 : RESERVED_INPUT_WITH_WEAK_PULLUP : J7 : : : : 3 : CTRL_3V3_LPMOD_G : J8 : output : 3.3-V LVTTL : : 3 : Y QSFP_MODPRS_A : J9 : output : 1.8 V : : 5 : Y QSFP_RST_G : J10 : input : 1.8 V : : 5 : Y VCCIO5 : J11 : power : : 1.8V : 5 : QSFP_LPMOD_C : J12 : input : 1.8 V : : 5 : Y QSFP_AUX_3 : J13 : bidir : 1.8 V : : 5 : Y QSFP_INT_A : K1 : output : 1.8 V : : 2 : Y QSFP_RST_C : K2 : input : 1.8 V : : 2 : Y VCCIO2 : K3 : power : : 1.8V : 2 : VCCA1 : K4 : power : : 3.0V/3.3V : : CTRL_3V3_LPMOD_B : K5 : output : 3.3-V LVTTL : : 3 : Y RESERVED_INPUT_WITH_WEAK_PULLUP : K6 : : : : 3 : RESERVED_INPUT_WITH_WEAK_PULLUP : K7 : : : : 3 : CTRL_3V3_MODSEL_G : K8 : output : 3.3-V LVTTL : : 3 : Y VCCA4 : K9 : power : : 3.0V/3.3V : : QSFP_MODSEL_J : K10 : input : 1.8 V : : 5 : Y QSFP_LPMOD_F : K11 : input : 1.8 V : : 5 : Y QSFP_LPMOD_H : K12 : input : 1.8 V : : 5 : Y RESERVED_INPUT_WITH_WEAK_PULLUP : K13 : : : : 5 : RESERVED_INPUT_WITH_WEAK_PULLUP : L1 : : : : 2 : QSFP_LPMOD_B : L2 : input : 1.8 V : : 2 : Y QSFP_LPMOD_E : L3 : input : 1.8 V : : 2 : Y CTRL_3V3_RST_A : L4 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_RST_C : L5 : output : 3.3-V LVTTL : : 3 : Y VCCIO3 : L6 : power : : 3.3V : 3 : VCCIO3 : L7 : power : : 3.3V : 3 : VCCIO3 : L8 : power : : 3.3V : 3 : GND : L9 : gnd : : : : CTRL_3V3_LPMOD_F : L10 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_RST_G : L11 : output : 3.3-V LVTTL : : 3 : Y QSFP_MODSEL_H : L12 : input : 1.8 V : : 5 : Y QSFP_MODPRS_B : L13 : output : 1.8 V : : 5 : Y QSFP_MODSEL_C : M1 : input : 1.8 V : : 2 : Y QSFP_MODSEL_B : M2 : input : 1.8 V : : 2 : Y QSFP_RST_H : M3 : input : 1.8 V : : 2 : Y CTRL_3V3_LPMOD_E : M4 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_RST_D : M5 : output : 3.3-V LVTTL : : 3 : Y GND : M6 : gnd : : : : RESERVED_INPUT_WITH_WEAK_PULLUP : M7 : : : : 3 : RESERVED_INPUT_WITH_WEAK_PULLUP : M8 : : : : 3 : RESERVED_INPUT_WITH_WEAK_PULLUP : M9 : : : : 3 : CTRL_3V3_MODSEL_J : M10 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_LPMOD_C : M11 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_MODSEL_H : M12 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_MODPRS_B : M13 : input : 3.3-V LVTTL : : 3 : Y GND : N1 : gnd : : : : QSFP_MODSEL_A : N2 : input : 1.8 V : : 2 : Y QSFP_RST_D : N3 : input : 1.8 V : : 2 : Y CTRL_3V3_RST_H : N4 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_MODSEL_B : N5 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_INT_A : N6 : input : 3.3-V LVTTL : : 3 : Y CTRL_3V3_RST_E : N7 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_MODSEL_C : N8 : output : 3.3-V LVTTL : : 3 : Y CTRL_3V3_LPMOD_J : N9 : output : 3.3-V LVTTL : : 3 : Y RESERVED_INPUT_WITH_WEAK_PULLUP : N10 : : : : 3 : RESERVED_INPUT_WITH_WEAK_PULLUP : N11 : : : : 3 : CTRL_3V3_LPMOD_H : N12 : output : 3.3-V LVTTL : : 3 : Y GND : N13 : gnd : : : :